NXLog Docs

UDP (om_udp)

This module sends log messages as UDP datagrams to the address and port specified. UDP is the transport protocol of the legacy BSD Syslog standard as described in RFC 3164, so this module can be particularly useful to send messages to devices or Syslog daemons which do not support other transports.

Configuration

The om_udp module accepts the following directives in addition to the common module directives. The Host directive is required.

Host

The module connects to the IP address or hostname defined in this directive. If additional hosts are specified on new lines, the module works in a failover configuration. If a destination becomes unavailable, the module automatically fails over to the next one. If the last destination becomes unavailable, the module fails over to the first destination.

When the Host directive is used with a hostname instead of an IP address, the the hostname will be resolved to an IP address for each new connection. If a resolver, e.g. DNS, returns multiple IP addresses, the module will connect to the first IP address. If a single output instance is configured with multiple Host directives or the resolver returns multiple addresses for a name, these hosts are accessed in failover mode. If a Host directive is configured with a hostname, the product performs a name lookup and establishes the connection to the first reachable address in the returned set of addresses. The module will remain connected to that address until it is stopped, or the connection is severed. DNS changes are therefore not picked up by the module without intervention. If the connection fails to the first address of the set, the module will attempt to connect to the next address, until it reaches the end of the set of addresses. Then it performs a lookup on the next Host directive, if so configured. Once all options are exhausted, the module will start over from the first Host directive, cycling through them again until connection can be reestablished.

The port number can be defined by appending it at the end of the hostname or IP address using a colon as a separator (host:port). For each destination with no port number defined here, the port number specified in the Port directive is used. Port numbers defined here take precedence over any port number defined in the Port directive. The default port is 514.

Because of the nature of the UDP protocol and how ICMP messages are handled by various network devices, the failover functionality in this module is considered as "best effort". Detecting hosts going offline is not supported. Detecting the receiving service being stopped - while the host stays up is supported.
Port

The module connects to the port number on the destination host defined in this directive. This configuration is only used for any destination in the Host directive which does not have a port specified. If no port is configured for a destination in either directive, the default port is used, which is port 514.

The Port directive is deprecated and will be removed from NXLog EE 6.0. After that, the port can only be defined in the Host directive.

LocalPort

This optional directive specifies the local port number of the connection. If this is not specified, a random high port number will be used, which is not always ideal in firewalled network environments.

Due to the required TIME-WAIT delay in closing connections, attempts to bind to LocalPort may fail. In such cases, the message Address already in use will be written to nxlog.log. If the situation persists, it could impede network performance.

OutputType

See the OutputType directive in the list of common module directives. If this directive is not specified, the default is Dgram.

Reconnect

This optional directive sets the reconnect interval in seconds. If it is set, the module attempts to reconnect in every defined second. If it is not set, the reconnect interval will start at 1 second and doubles with every attempt. If the duration of the successful connection is greater than the current reconnect interval, then the reconnect interval will be reset to 1 sec.

The Reconnect directive must be used with caution. If it is used on multiple systems, it can send reconnect requests simultaneously to the same destination, potentially overloading the destination system. It may also cause NXLog to use unusually high system resources or cause NXLog to become unresponsive.
SockBufSize

This optional directive sets the socket buffer size (SO_SNDBUF) to the value specified. If this is not set, the operating system default is used.

Procedures

The following procedures are exported by om_udp.

reconnect();

Force a reconnection. This can be used from a Schedule block to periodically reconnect to the server.

The reconnect() procedure must be used with caution.

If configured, it can attempt to reconnect after every event sent, potentially overloading the destination system.

Examples

Pre-v5 syntax examples are included, they will become invalid with NXLog EE 6.0.

Example 1. Sending Raw Syslog over UDP

This configuration reads log messages from socket and forwards them via UDP.

nxlog.conf
<Input uds>
    Module  im_uds
    UDS     /dev/log
</Input>

<Output udp>
    Module  om_udp
    Host    192.168.1.1:1514
</Output>
# Using the syntax prior to NXLog EE 5,
# where the port is defined in a separate directive.
#<Output udp>
#    Module  om_udp
#    Host    192.168.1.1
#    Port    1514
#</Output>

<Route uds_to_udp>
    Path    uds => udp
</Route>
Example 2. Sending Logs over UDP with Failover

This configuration sends logs via UDP in a failover configuration (multiple Hosts defined).

nxlog.conf
<Output udp>
    Module  om_udp
    Host    192.168.1.2:1514
    Host    192.168.1.3:1514
    Host    example.com:1234
</Output>