APC Automatic Transfer Switch

The APC Automatic Transfer Switch (ATS) is capable of sending its logs to a remote Syslog destination via UDP.

Log sample
Date        Time      Event
------------------------------------------------------------------------
03/26/2017  16:20:55  Automatic Transfer Switch: Communication
                      established.
03/26/2017  16:20:45  System: Warmstart.
03/26/2017  16:19:13  System: Detected an unauthorized user attempting
                      to access the SNMP interface from 192.168.15.11.

The ATS is an independent device, so if there is more than one installation in a particular environment, the configuration below must be applied to each device individually. For more details about configuring APC logs, go to the APC Support Site and select the product name or part number.

The steps below have been tested on AP7700 series devices and should work for other ATS models also.
  1. Configure NXLog Agent to receive logs via UDP (see the example below). Then restart NXLog Agent.

  2. Make sure NXLog Agent is accessible from the device.

  3. Configure Syslog logging on the ATS using either the web interface or the command line. See the following sections.

Example 1. Receiving APC ATS logs

The following examples show the ATS logs as received and processed by NXLog Agent.

nxlog.conf
<Extension _syslog>
    Module  xm_syslog
</Extension>

<Extension _json>
    Module  xm_json
</Extension>

<Input in_syslog_udp>
    Module  im_udp
    Host    0.0.0.0
    Port    514
    Exec    parse_syslog();
</Input>

<Output file>
    Module  om_file
    File    "/var/log/apc.log"
    Exec    to_json();
</Output>

Logs like the example at the beginning of the chapter will produce the following output.

Output sample
{
  "MessageSourceAddress": "192.168.15.22",
  "EventReceivedTime": "2017-03-26 17:03:27",
  "SourceModuleName": "in_syslog_udp",
  "SourceModuleType": "im_udp",
  "SyslogFacilityValue": 23,
  "SyslogFacility": "LOCAL7",
  "SyslogSeverityValue": 7,
  "SyslogSeverity": "DEBUG",
  "SeverityValue": 1,
  "Severity": "DEBUG",
  "Hostname": "192.168.15.22",
  "EventTime": "2017-03-26 16:04:18",
  "SourceName": "System",
  "Message": "Detected an unauthorized user attempting to access the SNMP interface from 192.168.15.11. 0x0004"
}
{
  "MessageSourceAddress": "192.168.15.22",
  "EventReceivedTime": "2017-03-26 17:20:04",
  "SourceModuleName": "in_syslog_udp",
  "SourceModuleType": "im_udp",
  "SyslogFacilityValue": 23,
  "SyslogFacility": "LOCAL7",
  "SyslogSeverityValue": 7,
  "SyslogSeverity": "DEBUG",
  "SeverityValue": 1,
  "Severity": "DEBUG",
  "Hostname": "192.168.15.22",
  "EventTime": "2017-03-26 16:20:54",
  "SourceName": "System",
  "Message": "Warmstart. 0x0002"
}
{
  "MessageSourceAddress": "192.168.15.22",
  "EventReceivedTime": "2017-03-26 17:20:04",
  "SourceModuleName": "in_syslog_udp",
  "SourceModuleType": "im_udp",
  "SyslogFacilityValue": 23,
  "SyslogFacility": "LOCAL7",
  "SyslogSeverityValue": 7,
  "SyslogSeverity": "DEBUG",
  "SeverityValue": 1,
  "Severity": "DEBUG",
  "Hostname": "192.168.15.22",
  "EventTime": "2017-03-26 16:20:55",
  "Message": "Automatic Transfer Switch: Communication established. 0x0C05"
}

Configuring via the web interface

  1. Log in to the web panel.

  2. Go to Network  Syslog.

  3. Enable Syslog.

  4. Select the Facility.

  5. Add up to four Syslog servers and a port for each.

  6. Map the Local Severity to the Syslog Severity as required.

    Syslog Configuration
  7. Click Apply.

Configuring via the command line

  1. Log in to the ATS via Telnet.

  2. Type 2 and then 9 to go to the Syslog settings.

  3. Type 1 to configure the Syslog settings.

  4. Type 1 to enable Syslog.

  5. Type 2 to configure the Syslog facility.

  6. Type 3 to save the changes.

  7. Press ESC to go one level up.

  8. Select one of the four Syslog server slots.

  9. Type 1 to set the Syslog server IP address.

  10. Type 2 to change set the UDP port number.

  11. Type 3 to apply the changes.

  12. Press ESC to go one level up.

  13. Type 6 to map the local severity to the Syslog severity.

  14. Use options from 1 to 4 to choose the mapping.

  15. Type 5 to accept the changes.

Example 2. ATS syslog settings

The following shows the Syslog settings screen, which is shown after completing step 2 above.

------- Syslog ---------------------------------------------------------

    Syslog Settings               Severity Mapping
    --------------------------------------------------------------------
    Syslog  : Enabled             Severe : DEBUG          Info: DEBUG
    Facility: LOCAL7              Warning: DEBUG          None: DEBUG

    #  Syslog Server Port   IP
    --------------------------------------------------------------------
    1  514                192.168.15.251
    2  514                0.0.0.0
    3  514                0.0.0.0
    4  514                0.0.0.0

     1- Settings
     2- Server 1
     3- Server 2
     4- Server 3
     5- Server 4
     6- Severity Mapping

     <ESC>- Back, <ENTER>- Refresh, <CTRL-L>- Event Log
> 1
Disclaimer

While we endeavor to keep the information in our guides up to date and correct, NXLog makes no representations or warranties of any kind, express or implied about the completeness, accuracy, reliability, suitability, or availability of the content represented here. We update our screenshots and instructions on a best-effort basis.

Last revision: 17 September 2018